Complete Kitchen Remodel V.3 – Subfloor and Electrical

This is video number 3 of a complete – COMPLETE – kitchen remodel. This video series includes demo, floor joist repair/replacement, sub-floor install (this video), cement board under lament install, tile, electrical (this video), drywall, paint, cabinet install, new counter tops, and finally all finish carpentry = job done!

In this video we complete install of the new subfloor and begin re-wiring this old kitchen…we’ll continue electrical and complete insulation installation in video 4 of this series – so please subscribe so you don’t miss seeing this project come together!

Purchase the circuit tester at Amazon: https://amzn.to/2JClzFc

Questions? Contact us at DoAndBrew@gmail.com

Support Do& Brew at www.Patreon.com/DoAndBrew

Also, Do & Brew is now featuring the music of Jonivan Jones! Find out more about this soulful Western Blues Folk singer / songwriter at:

JonivanJonesMusic.com

and check out his YouTube channel at:

youtube.com/user/badfolk

32 Comments

  1. Rome on September 30, 2020 at 8:19 am

    I’m enjoying these vids. Very detailed for DIYers. Thanks!

  2. Terry Scott on September 30, 2020 at 8:22 am

    Thanks for the video, I found it helpful as I had to repair three 14 foot floor joist in my 1940’s home. I used this video as my guide. I have a question, in sistering the new joist, I found that there is a slight but noticeable difference in the height of the old versus new joist. Do I need to be concerned about this? I suppose I could plane them down some to level things out, but is this necessary? When would you be concerned about the height difference? I would appreciate your thoughts? Thanks.

  3. JJC on September 30, 2020 at 8:24 am

    Great videos Sr!!👍🏽

  4. ABE ZOOTS on September 30, 2020 at 8:25 am

    My ocd hates that you left it dirty under subfloor

  5. State of Peaches on September 30, 2020 at 8:25 am

    I subscribed, he’s a great teacher! I am working on a similar type project and to save cost I’m doing a portion of the work myself. His videos has been an excellent source of instruction and knowledge.

  6. Marek Włodarczyk on September 30, 2020 at 8:35 am

    Very helpfull video. Thanks

  7. bbtank3000 on September 30, 2020 at 8:36 am

    This guy deserves more views. He explains every step with viewable camera angles!

  8. Go Malibu Surf on September 30, 2020 at 8:37 am

    Thank you for all your great videos.

    @4:25 you stated, you never want 4 corners to intersect. For the rookies, please clarify the reason.

  9. ddrusa on September 30, 2020 at 8:37 am

    Finally a channel that no can get used to thank you for the tips. Our house is the same way with subflooring

  10. Mr. Wizeguy on September 30, 2020 at 8:38 am

    I don’t get it, constantly similar videos here in YT where floor and some joist are rotted and you doesn’t replace all of them. Wood can’t be so expensive that it’s worth to sister joist and leave some possible partially rotted wood.

  11. Graham Cole on September 30, 2020 at 8:38 am

    Why don’t you use some wood preserver over the new joists?

  12. steven Gao on September 30, 2020 at 8:39 am

    thanks for this video, but why you suggest 4 corner of plywood do not intercept together ? I mean what is the reason not to. thanks

  13. hkgonra on September 30, 2020 at 8:41 am

    What screws are you using for the subfloor ?

  14. Hippie Lewis on September 30, 2020 at 8:42 am

    Why do you put loud ass music in with it stupid

  15. Bad Atheist on September 30, 2020 at 8:43 am

    why are you not using tongue and groove osb?

  16. Graham Cole on September 30, 2020 at 8:44 am

    In Britain we use plastic clips to hold the cables rather than metal.

  17. Gary L. Moore on September 30, 2020 at 8:49 am

    Did this floor require a vapour barrier?

  18. Sam S on September 30, 2020 at 8:50 am

    Great music tracks. 👍

  19. Janet Stone on September 30, 2020 at 8:53 am

    You are inspiring me, to finish my remodeling – I am a single, private school teacher, doing it all myself. THANK YOU!

  20. naveod on September 30, 2020 at 8:57 am

    do you think spraying car undercoating on the beams would be a good ideal to keep moisture away from the beams

  21. Shaun Louis on September 30, 2020 at 8:57 am

    Are metal nail plates required on the studs to protect the electrical wiring from nails etc?

  22. Archie Braza on September 30, 2020 at 8:59 am

    Danm, very nice job,,,,,,

  23. Mona Me on September 30, 2020 at 9:03 am

    Do you have a video showing the wiring process for a series of can lights and for a series of outlets? I would appreciate it.

  24. Ed Cox on September 30, 2020 at 9:04 am

    Water pipes were to old..why not replace when joist cut out ??????

  25. Tj on September 30, 2020 at 9:04 am

    I have a few comments about the electrical part. You can not install BX wire into a plastic box. Has to be metal. And the wire in a kitchen needs to be 12awg not 14. But over all i think the floor looked good.

  26. mtgentry on September 30, 2020 at 9:04 am

    My dad: "Nah, we don’t need to turn the power off – just don’t touch any of the wires in the box and you’ll be fine"

  27. Sam S on September 30, 2020 at 9:05 am

    Songs are great and your work as well brother.

  28. Enrique Felix jr. on September 30, 2020 at 9:06 am

    Awesome video very helpful

  29. aecguy on September 30, 2020 at 9:09 am

    The only thing guys after a great vid you didn’t clean the void of rubbish.

  30. Ingrid De La Luz on September 30, 2020 at 9:11 am

    So fix a sub floor do the ends have to meet end from end. With it being an attic floor it will be difficult to reach

  31. Alejandra Montelongo on September 30, 2020 at 9:13 am

    Hello , I had a quick question. My subfloor and the backer board are laid. As I walk acroos there are areas where the floor is sunken as I walk . Is that normal ?

  32. Abe Rum on September 30, 2020 at 9:15 am

    Im subscribed!! very relevant material!

Leave a Comment